Search:

Type: Posts; User: gnuuser

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. living out there in mass. i would most likely...

    living out there in mass. i would most likely change the coax and or the antenna both.
    I suspect with a high probability that its water inclusion and possibly salt corrosion due to close proximity...
  2. dont be afraid to experiment with old junk parts...

    dont be afraid to experiment with old junk parts to see what they do.
    learning electronics is fun and rewarding when you build something and it works.
    If it doesnt then you troubleshoot step by...
  3. Replies
    11
    Views
    374

    cut apart a junk antenna to get pics for him...

    cut apart a junk antenna to get pics for him
    1147
    1148
    1149
    It takes two of these shims to keep the shaft centered.

    its difficult to see but the end of the tube has two small holes drilled...
  4. Replies
    11
    Views
    374

    i cant find a picture on the web but as best...

    i cant find a picture on the web but as best describes them
    one tube slides inside another a bit loose,
    then thin sheets of copper or brass are formed to fit between the inner wall of the lower...
  5. Replies
    11
    Views
    374

    usually there is couple of small copper shims...

    usually there is couple of small copper shims inserted in holes at the bottom of each section that are stopped by the rolled in top edge.
    if one of these comes apart then the shims have broken off....
  6. Replies
    7
    Views
    349

    that looks so cool !

    that looks so cool !
  7. Replies
    11
    Views
    374

    quality aside often the ambient temperature can...

    quality aside often the ambient temperature can affect the manufacturing process (IE. hotter expands and cooler contracts)
    an item made in a warm climate will often shrink slightly in a cold climate...
  8. once you have a few posts in (it may take 5 or...

    once you have a few posts in (it may take 5 or 6)and are logged in click on settings,
    in the box that says my settings you should see edit profile, edit avatar, edit signature etc.
    click on edit...
  9. Replies
    7
    Views
    349

    i know what you mean! usually i store equipment...

    i know what you mean!
    usually i store equipment for a short time before stripping them out. (but then kick myself in the butt a few weeks after scrapping the chassis)!
    worst part is trying to find...
  10. Replies
    4
    Views
    295

    usually swaged on (a form of compression without...

    usually swaged on (a form of compression without deformation)
    depending on the material the corona ball can be drilled out and soldered in place.
    even with extreme power output you are not going to...
  11. Replies
    7
    Views
    349

    visible cw monitor (for deaf)

    Im currently researching and possibly designing a module that can be plugged into the earphone jack of a cw radio with filtering to pick up the strongest signals and convert the code pulses to light...
  12. scavanging, scrounging, and repourposing electronics. ORGANIZE!

    we all do it to some extent! especially those of us who homebrew.
    salvaging parts from old electronics.
    example:
    as a recycle pro i come into contact with many types of electronics.
    the wireless...
  13. Replies
    8
    Views
    540

    the problem is primarily because what is legal in...

    the problem is primarily because what is legal in one country may not be in another!
    with manufacturing in china or other countries their equipment is built to their legal standards and sold at much...
  14. Replies
    1
    Views
    830

    CW that was a very informative and funny video!...

    that was a very informative and funny video!
    perfect morse with a straight key or bug or paddles is never perfect because timing differences between operators.
    you could be sending at 15wpm and the...
  15. Replies
    3
    Views
    396

    after further study of this idea it would be far...

    after further study of this idea it would be far too broadband to suit the purpose of just one frequency. and would probably broadcast a lot of spurious interference.
    a properly constructed cage...
  16. the also appear to be french made radios. ...

    the also appear to be french made radios. interesting to collectors or someone who would probably restore or modify them.
  17. pulling that many teeth is a real b**ch! if you...

    pulling that many teeth is a real b**ch!
    if you can get it cbd oil rubbed in the cheeks and jawbone around where teeth were pulled will help a lot
    and there is some cbd oil you can apply under the...
  18. Id be glad and Honored to help moderate! (Ive...

    Id be glad and Honored to help moderate! (Ive been one on linuxinternationals for quite a few years now) so its no problem for me at all.
    was on lgu forum, Handsonautomation forum, ark forum and...
  19. set your closest repeaters to the areas you...

    set your closest repeaters to the areas you travel the most.
    in your computer create separate settings files for chirp that you can upload to your radio in the event you travel outside your normal...
  20. Replies
    6
    Views
    1,172

    yeah I see what you mean there. bent backwards...

    yeah I see what you mean there.
    bent backwards against a clamp can cause the tape measure to tear especially if it has been heated to solder.
  21. mx linux while easy to learn and use has its own...

    mx linux while easy to learn and use has its own foibles to deal with.
    debian ham radio pureblend, and andy's ham linux come with the software already built in.
    andy's ham linux is easy to install...
  22. Replies
    6
    Views
    1,172

    when your working with pvc fittings you need to...

    when your working with pvc fittings you need to take into account the internal shoulders (they were designed to prevent the pipe from going too far into the intersecting paths and blocking water...
  23. Thread: MTM800E

    by gnuuser
    Replies
    2
    Views
    299

    Mobile Radios Do you have the manual? check the manual first...

    Do you have the manual?
    check the manual first and or check the manufacturers website support.
  24. Thread: Hams and 11m

    by gnuuser
    Replies
    31
    Views
    14,309

    usually i have to remind some operators that foul...

    usually i have to remind some operators that foul language violates fcc rules! Some apologize and some go off on a rant
    but once i stated that some authorities often do monitor the channels and the...
  25. Thread: Hams and 11m

    by gnuuser
    Replies
    31
    Views
    14,309

    not necessarily so! I prefer to talk to others as...

    not necessarily so! I prefer to talk to others as if they are equals but i state pm me if you wish clarification on a subject.
    I do not talk down or snobby to anyone but consider it an honor to have...
Results 1 to 25 of 154
Page 1 of 7 1 2 3 4